Edexcel GCSE Combined Science Paper 6: Physics 2 Higher June 2018 question paper 1SC0/2PH

A student uses the apparatus in Figure 1 to determine the specific heat capacity of water.

State the measurements needed to calculate the specific heat capacity of water.

State two ways that the apparatus could be adapted to improve the procedure.

The student decides to measure the temperature of the water every minute while it is being heated.

Figure 2 shows a graph of the student’s results.

Predict the temperature of the water if the heating continues up to 8 minutes.

temperature of the water =_........ °C

Another student decides to melt some ice.

The student melts 380 g of ice at 0 °C.

The specific latent heat of fusion of ice is 3.34 × 10⁵J/kg.

Calculate the thermal energy needed to melt the ice.

Select an equation from the list of equations at the end of this paper.

thermal energy needed =_........ J

A cyclist is riding a bicycle at a steady velocity of 12 m/s.

The cyclist and bicycle have a total mass of 68 kg.

Calculate the kinetic energy of the cyclist and bicycle.

Use the equation

kinetic energy =_........ J

Describe the energy transfers that happen when the cyclist uses the brakes to stop.

The cyclist starts to cycle again.

The cyclist does 1600 J of useful work to travel 28 m.

Calculate the average force the cyclist exerts.

average force =_........ N

An athlete uses a training machine in a gym.

The display on the machine shows the time spent on the machine and the amount of energy transferred during a training session.

Figure 3 shows the displays for two different sessions by the same athlete.

Explain what the displays show about the average power of the athlete in each of these two sessions.

A student has a bar magnet, a piece of iron the same size as the magnet, and some paper clips.

Describe how the student could use these items to demonstrate temporary induced magnetism.

A student sets up the apparatus shown in Figure 4.

When the current in the solenoid is switched on, the solenoid attracts the iron nail.

Describe how the student could use this apparatus to investigate how the size of the current in the solenoid affects the force of attraction between the solenoid and the iron nail.

The spring constant of a different spring is 24 N/m.

The spring is extended from its unstretched length by 12 cm.

Calculate the energy transferred in extending the spring by 12 cm.

Use an equation selected from the list of equations at the end of this paper.

energy transferred =_........ J

Figure 5 shows the vertical forces on an aeroplane.

Use information from the diagram to determine the size and direction of the resultant vertical force on the aeroplane.

size =_........ kN, direction is_........

The aeroplane is descending.

Figure 6 shows a diagram of the resultant vertical and horizontal forces on the aeroplane as it is descending.

Complete the diagram to show the resultant of these two forces.

The mass of the aeroplane is 750 kg.

Calculate the change in gravitational potential energy of the aeroplane as it descends from 1300 m to the ground.

Gravitational field strength (g) = 10 N/kg

energy =_........ J

The aeroplane is powered by an engine that burns fuel.

The fuel supplies a total of 6500 kJ of energy every minute.

The efficiency of the engine is 0.70 (70%).

Calculate the power output of the engine.

Give your answer in kW.

power =_........ kW

Explain why the efficiency of the engine is less than 1 (100%).

A resistor is connected to a power supply.

The potential difference across the resistor is 6.0 V.

Which of these corresponds to a potential difference of 6.0 V?

The resistor remains connected for a period of time.

The current in the resistor is 200 mA.

A total charge of 42 C flows through the resistor.

Calculate, in minutes, the time taken for this amount of charge to flow through the resistor.

time =_........ minutes

Calculate the total energy transferred by the 6.0 V power supply when a charge of 42 C flows through the resistor.

energy =_........ J

The resistor becomes warm while there is a current in it.

Explain why the resistor becomes warm.

Figure 7 shows a cardboard tube with a wire coming out from each end.

There are two 10 ohm resistors inside the cardboard tube.

A potential difference of 6.0 V is connected between P and Q.

There is a current of 1.2 A in the wires.

Deduce how the resistors have been arranged inside the cardboard tube.

Figure 8 shows identical filament lamps connected together to a 12 V power supply.

Calculate the potential difference across each lamp.

potential difference =_........ V

The power output of each lamp is 0.75 W

Calculate the resistance of each lamp.

resistance =_........ Ω

*(b) Explain, with the aid of a circuit diagram, the method a student could use to investigate how the resistance of a single lamp changes with the potential difference across the lamp.